Product Details
TrolMaster (TSH-1) Temperature / Humidity Station
TrolMaster's TSH-1 Temperature / Humidity Station is a 0-10 volt analog output control station that works with the HCS-1 and HCS-2 controllers. The TSH-1 can be configured to control either a temperature or a humidity device that requires a variable 0-10 volt input signal.
The TSH-1 is capable of controlling variable speed fans, vents or any other device that accepts a 0-10 volt input. It features separate day and night “idle” speed settings built-into the TSH-1 as well as separate Day / Night setpoints accessed through the HCS controller.
Features & Benefits:
LCD Display, Easy Operation
Seamless Connection with Hydro-X or Hydro-X Pro
Micro-SD slot for Firmware Upgrade
Assignable control of Humidity or Temperature
Plug & Play
Package Content:
1 x Temperature/Humidity Station (TSH-1)
1 x 16ft RJ12 Cable
1 x 4ft RJ12 Cable
1 x RJ12 T-Splitter
Product Details
TrolMaster(DST-1) Temperature Device Station for Hydro-X System
The TrolMaster DST-1 Temperature control modules allow user to easily connect and control standard heating or cooling devices to the Hydro-x. Any heating or cooling device that is 10-amps at 120 volts or less can be controlled by the DST-1.
Comes with a cable set.
Features & Benefits:
LED Indicator
Attaching Plug
RJ12 Cable Socket
Address Assignment
Plug & Play
Package Content:
1 x Device Station
1 x 16ft RJ12 Cable
1 x 4ft RJ12 Cable
1 x RJ12 T-Splitter
TrolMaster (ECS-9) 12ft RJ12 to 4-pin IP65 Connector Cable
TrolMaster's ECS-9 RJ12 to 4pin connector cable is simply a 12 ft cable to use with Lighting Control Adapter T (LMA-T) and ThinkGrow LEDs with Threaded Waterproof Connectors for interconnecting.
Features & Benefits:
Seamless Connection
Plug & Play
Package Content:
1 x ECS-9 12ft RJ12 to 4-pin IP65 connector cable
Specification:
Working Environments: Temperature 32-122°F, Humidity=90%
Product Details
TrolMaster (SPH-1) RJ12 Splitter Hub
The SPH-1 Splitter Hub from TrolMaster makes the installation of our controllers as easy as plugging in a phone cable. The SPH-1 hub uses a single RJ12 cable input jack, and provides (8) individual RJ12 output jacks that can be connected to various TrolMaster sensors, adapters and device modules. Using the SPH-1 allows for a "clean" installation and eliminates the need for daisy-chain Y-splitters to be used to interconnect multiple modules or sensors.
The SPH-1 is also a powered hub, meaning that it will boost the signals passing through the SPH-1 allowing more modules, sensors and light adapters to be connected to the TrolMaster controllers. By using the SPH-1, an almost unlimited number of LED / HID lights can be controlled using a single TrolMaster controller. The SPH-1 comes complete with the SPH-1 hub, a 16 foot RJ12 cable and the 12vdc power supply.
The SPH-1 can be located in a central location with a single RJ12 cable connecting it to the main controller. From the SPH-1 hub, the individual RJ12 jacks can be connected to each of the sensors, device modules, or lighting adapters.
NOTE: If you are using the SPH-1 to interconnect your lighting systems together back to a single LMA adapter (except for LMA-T and ThinkGrow light system), DO NOT connect the 12 volt dc power supply to the SPH-1.
Features & Benefits:
LED indicator
Plug & Play
Package Content:
1x RJ12 Splitter Hub
1x 12V Power Adapter
1x 4 ft RJ12 Cable
TrolMaster (WCS-3) Water Content Sensor 3
The TrolMaster WCS-3 Water Content Sensor 3 is specifically designed to measure the moisture level (in percentage) of the grow medium. The WCS-3 can be used with the TrolMaster Aqua-X (NFS-1), Aqua-X Plus (NFS-3), Aqua-X Pro (NFS-2), Hydro-X Pro (HCS-2) and Tent-X (TCS-1) control systems. Each WCS-3 sensor is a 3-prong Volumetric Water Content (VWC) sensor. To use the W CS-3, you will insert the 3-prong sensor into the grow medium such as coir , soil or rock wool to be measured. You can connect multiple Medium Moisture Sensors to a single controller. Up to 5 0 WCS-3 can be connected to the NFS-2 and HCS-2 controllers, 20 o n the NFS-3, 8 on the NFS-1 controller, and 1 o n the TCS-1 controller. *NOTE: The TCS-1 can only have a single WCS-3 connected. Each WCS-3 features a built-in LCD display on one side of the sensor that becomes “live” and can be viewed when the sensor is shaken or disturbed. The display will show the current VWC% reading right on the sensor.
Features & Benefits:
Ultra-slim simplicity design
Tap-to-wake LCD Display
Crop-steering irrigation compatible
Designed for Daisy-chain multiple sensors
Real-time measuring of water content
Alarm and mobile notification when setpoint exceeded
Package Content:
1x Water Content Sensor3
1x M12 T-splitter
1x 4ft M12 Cable
Specification - Absolute Maximum Ratings:
Input Voltage : 12V = 0.1A
Input Current : 100-200 mA
Operating Temperature : 32°-122°F
Humidity : ≤90% RH
Packaging Dimensions: 170mm(L) x 90mm(W) x 54mm(H)
The 4RS-1 is a universal 4-outlet power expansion module. It can be used with any of TrolMaster’s “plug-in” style device modules to expand the number of devices that can be controlled by the Hydro-x. A single 120-240 volt “trigger” cable on the 4RS-1 connects to your device / control module. When the device module is activated by the Hydro-x, the 4RS-1 trigger cable will turn on each of the 4 receptacles on the 4RS-1 with a 3 second time delay between each outlet being activated. That minimizes high start-up (inrush current) and allows up to 4 devices to be safely controlled. The 4RS-1 must be installed with a 120/240 volt power circuit (up to 50-amps @ 240vac). Three wire terminals inside the unit accept up to #6 AWG wire making connections to the power source easy.
The Hydro-X Plus / HCS-3 system is a professional-grade single-zone environmental control system that can control your entire grow space. It has an 800x480 7” LED display monitor and can control an unlimited number of lights, 8 temperature devices, 8 humidity devices, 4 CO2 devices, and 12 programmable timer devices (up to 50 schedules can be created). With incredible flexibility and the expanded product capacity, anyone can now easily customize their own grow room control system for maximum yields. Having multiple control modules also provides the option for the user to create multiple "stages" of temperature and humidity control, which will provide a more stable environment.
The HCS-3 system comes with an MBS-PRO 4-in-1 sensor to measure temperature, humidity, CO2 ppm, and the presence of light. Lighting control has never been easier or more capable. The optional MBS-PAR light sensor can be added to the system. It will automatically adjust light intensity to precisely provide the exact amount of illumination for optimum plant growth. The Hydro-X Plus has been can also track your DLI levels. Having 2 separate lighting control channels allows the user to create multiple lighting layouts (and dimming sequences) based on their individual preferences.
Besides controlling your room, if a problem is detected by the HCS-3, a warning message (notification) will be sent to your smartphone. Up to 10 smoke detectors and 10 water leak-detectors can be connected to the HCS-3 which will alert you if there are any fire or water leaks. The HCS-3 also offers multiple advanced functions to control your entire grow room or greenhouse such as Sunrise / Sunset simulation, DLI control, overheat protection, Spectrum & Group lighting control, and more.
HS-1 Humidistat Station is specifically designed to control dehumidifier in the Hydro-X Control System. It will control your dehumidifier by Day/Night setpoint base on the photocell status. Connect the HS-1 to where your thermostat is on the wall by using the preexisting wires, now you can use the HS-1 in conjunction with the Hydro-X to control dehumidifier easily.
TS-2 Thermostat Station is specifically designed to replace the traditional thermostat to control four system types of equipments (Heat/Cool, Cool only, Heat only, Heat pump). It will control your four system equipments by Day/Night setpoint base on the photocell status. Connect the TS-2 to where your thermostat is on the wall using preexisting wires, now you can use the TS-2 in conjunction with the Hydro-X to control heating & cooling equipments.
The Trolmaster DSV-1 is a low-voltage output module that can be used on the HCS-1, HCS-2 controllers. The DSV-1 can be addressed to be used as a temperature, humidity, CO2, or timer device module.Multiple voltage outputs are selectable by the user. The DSV-1 can output either 12 or 24 VDC up to .5 amps, or 12 or 24 VAC up to 4.8VA. Once the module is configured it will activate the low-volt device wired to the DSV-1.This allows the user to directly connect low voltage devices such as solenoids, valves, audio visual alarms or any other device that requires 12 to 24 volt AC or DC power to operate.
TrolMaster’s Hydro-X system can control most of the horticultural lighting fixtures sold on the market today. Most light manufacturers provide the ability to control their lighting systems using what known as a low-volt control. That low-volt control can take many forms and communication protocols. TrolMaster makes several types of lighting adapters (LMA units) that allow the Hydro-x to control lights using their low-volt control option. This Lighting Control Adapter D (LMA-12) is specially designed for controlling D ballast.
The TrolMaster pH probes provide accurate and reliable monitoring on the pH of the water being monitored by the Aqua-x. The PPH-1 probe connects to the Aqua-x via the AMP-2.
The WCS-1 water content sensor allows the user to monitor the % of water / nutrients within the growing medium. The moisture level / water content is displayed in real-time on the WCS module itself, the Aqua-x and the APP. That data is displayed on a graph (through the APP) and helps the user visualize the dry-down time, and to make adjustments to their irrigation timers / irrigation cycles. Up to 8 WCS-1 can be connected to a single Aqua-x. When multiple WCS-1 are connected to a single Aqua-X, the displayed value on the Aqua-x and APP will be the AVERAGE of all of the sensors.
The Trolmaster DSD-1 Dry-contact module provides a simple and flexible solution to who want to connect & control devices to the Hydro-X using a “dry-contact” or relay to activate the device. Some equipment requires either normally open or normally closed contact closure in order to activate the equipment. The DSD-1 is the product that you need to control those types of devices. *The DSD-1 can be configured to work as the other Trolmaster power modules work. The DSD-1 connects into the “devices” line on the Hydro-X and can be set to control an almost infinite number and types of devices such as:
Lighting contactors
Light Deprivation curtains
Pump contactors
Temperature devices
Humidity devices
CO2 devices
* Consult Trolmaster for questions concerning your particular device.
The TrolMaster DSP-1 program device module (timer module) works like a multi-function timer. The DSP-1 allows the user to easily connect any device that needs to be controlled by TIME to the Hydro-x. Any device that is 10-amps at 120 volts or less can be controlled by the DSP-1.
The ECS-4 extension cable is simply a 16 ft extension cable to use with the AMP-2 sensor board. It has a male and female end and can extend the distance between AMP-2 sensor board and the main controller.
The Hydro-X system is a professional-grade single zone environmental system. It is fully customizable and modularly designed. Installation is simple and the system is easy to expand upon. The Hydro-X system can control most grow lights brands, HVAC systems, mini-split air conditioners, commercial dehumidifiers and humidifiers, as well as CO2 generators or regulators. With the free TrolMaster App, the user can access all of the settings and alerts on the system from anywhere at anytime.
TrolMaster’s Hydro-X system can control most of the horticultural lighting fixtures sold on the market today. Most light manufacturers provide the ability to control their lighting systems using what known as a low-volt control. That low-volt control can take many forms and communication protocols. TrolMaster makes several types of lighting adapters (LMA units) that allow the Hydro-x to control lights using their low-volt control option.
The optional CO2 Sensor (MBS-S8) measures the CO2 PPM within the growing area. Using the MBS-S8 allows the users to connect and control their supplemental CO2 system using the Hydro-X. *Used in combination with one or more DSC-1 CO2 device modules."Sensors should remain dry and clean to prevent premature failure. Do not spray foreign substances or allow water / condensate on the sensors"
The TrolMaster DSH-2 Humidity control / device modules (240V) allow the user to easily connect and control standard humidifying or dehumidifying devices to the Hydro-x. The DSH modules are rated @ 10-amps. *Use with dehumidifiers less than 7 amps to avoid current overload.
The OA6-24 control board is designed to control multiple 24vac solenoid valves.It provides an easy and efficient method to control up to 6 valves… each with individual timer settings. Up to 5 OA6-24 can be connected to a single Aqua-x providing a maximum of 30 individually controlled outputs to connect to your solenoid valves. The Aqua-x can also provide a “master pump link” by using a DSP-1 along with the OA6-24. Connecting a DSP-1 to the OA6-24 provides an automatic “pump link” between the DSP-1 and the OA6-24. When any of the 24vac irrigation zones are activated on the OA6-24, the DSP-1 will automatically turn on the pump.
The TrolMaster EC & Temperature probes provide accurate and reliable monitoring on the EC and temperature of the water being monitored by the Aqua-x. The PCT-1 probe connects to the Aqua-x via the AMP-2.
The Aqua-X system is a professional-grade irrigation control system. It is a fully customizable modular designed system. Installation is simple and the system is easy to expand upon. The Aqua-X is designed to control up to 30 separate irrigation zones (24vac solenoid valves or 120vac pumps), The Aqua-x monitors pH / EC and water temp as well as to monitor actual growing medium moisture levels by using up to (8) Water Content Sensors connected to a single Aqua-x controller. The timers can be set-up to be recycling timers, or to operate at specific time of day and durations. With the free TrolMaster App, the user can access all of the settings and alerts on the system from anywhere at anytime. The NFS-1 is the brain of the Aqua-X system. It comes with a water detector WD-1 for leaking alert and watering confirmation.
The AMP-2 module connects the Aqua-x to a set of precision pH / EC & temperature probes to constantly measure the pH / EC & temperature of the water being sampled. The AMP-2 works with the TrolMaster PCT-1&2 and the PPH-1&2 probes. Once connected to the Aqua-x, the AMP-2 will display the sensor data on the Aqua-x and on the APP. The minimum and maximum “limits” can be set on the Aqua-x providing 24/7 notification of pH / EC or temperatures that are out of limits.
