ThinkGrow
-
ThinkGrow ThinkGrow LED Stand for ICL-300 (1 Base, 2 Posts)
The ThinkGrow LED Stand was specifically designed to be used with the ICL-300. With the use of the TSD-1, growers can easily place their ICL-300 lights within the canopy, as well as easily adjust the height of the lights. Additionally, this stand facilitates the task of daisy-chaining multiple ICL-300 grow lights. What's Included: 4x Stand Legs 2x Aluminium Tubes 1x M38 Screw Set 1x Dustproof Plug
$26.25
-
ThinkGrow ThinkGrow Model One 7' Splitter Power Cord, NEMA 5-15 Plug (TDC-120)
The Model One System offers a varied line of power cords, capable of satisfying the unique needs of every grower. From power cords that come with two-in-one use cases, to daisy-chain cords that come in several lengths to allow spacing freedom between the drivers, growers gain the ultimate freedom to customize their lighting setup in ANY grow room. This Daisy Chain Power Cord System is specially designed for the new Model-One System to interconnect between the LED drivers, the system can eliminate a massive amount of power outlets, and reduce the number of power cables required. Each “group” of Model One drivers must be connected to power using one of the TDC 120/240/240E power cables. The TDC-2/3/4 are used to connect the power and the control signal from one LED driver, to the next LED driver. What's Included: 1 x ThinkGrow TDC-120 7' Splitter Power Cord Specs: Input Voltage: 120VAC, 50/60Hz Amp: 10A AWG: 18 Length: 7’ Weight: 0.41 lbs (185 g) Temperature Range: 32~104℉
$18.90
-
ThinkGrow ThinkGrow Model One 2’ 18AWG Daisy Chain Cord (TDC-3)
The Model One System offers a varied line of power cords, capable of satisfying the unique needs of every grower. From power cords that come with two-in-one use cases, to daisy-chain cords that come in several lengths to allow spacing freedom between the drivers, growers gain the ultimate freedom to customize their lighting setup in ANY grow room. This Daisy Chain Power Cord System is specially designed for the new Model-One System to interconnect between the LED drivers, the system can eliminate a massive amount of power outlets, and reduce the number of power cables required. Each “group” of Model One drivers must be connected to power using one of the TDC 120/240/240E power cables. The TDC-2/3/4 are used to connect the power and the control signal from one LED driver, to the next LED driver. What's Included: 1 x ThinkGrow TDC-3 18AWG 2’ Daisy Chain Cord Specs: Input Voltage: 100-277VAC, 50/60Hz Amp: 10A AWG: 18 Length: 2’ (60cm) Weight: 0.27 lbs (122 g) Temperature Range: 32~104℉
$14.70
-
ThinkGrow ThinkGrow Model One 4' Inner Canopy LED Bar | Built-in 120W Driver (ICL-300)
ThinkGrow Model One Modular Lighting System ICL-300 When light is only applied from overhead lighting fixtures, it is often the case that the light does not reach the bottom of the canopy, leaving a lot of gains on the table. This is where the ICL-300 steps in and solves the problem. Equipped with a built-in driver and LED diodes covering 3 sides, the ICL-300 emits light in a 300 degree direction. When placed within the canopy, the lower sections of the plants can absorb light directly from the LED and can receive the much needed light they need to produce higher quality and quantity of yields. Additionally, by applying light to the middle of the plant structure, the user can eliminate lower quality flower formation and replace it with healthy flowers. The modular design of the ICL-300 allows them to be used in all installations regardless of the shape or size of the growing area. **Power Cord and Stand are not included with light** What's Included: 1x Inner Canopy LED bar w/ driver 2x mounting hooks 2x adjustment knobs
$229.99
