Hydro Systems
-
AutoPot AutoPot PotDivider for 2.2 or 3.9 Gallon Pots, Four Sections
PotDivider splits one AutoPot pot into four separate sections, so you can run four plants where one would normally go without making the system any bigger. It's made for pre-veg plants, tight-leaved varieties and herbs, and it lifts out with the plants when it's time to repot. 2.2 gal or 3.9 gal sizes Fits 1Pot trays, easy2grow trays and the Auto8 tray system Built-in AirBase: the partitioned base replaces the pebble layer Lifts out cleanly with the plants for repotting into the same pot Can't be used with an AirDome (the walls take up its space) In the box: 1 PotDivider with built-in AirBase.
$11.99 - $14.99
-
AutoPot AutoPot AirBase Drainage Plate, Square or Round, Optional AirDome
AirBase sits in the bottom of an AutoPot pot in place of a pebble drainage layer, so there's no more rinsing and pH-balancing clay pebbles at setup. It's tough, reusable ABS plastic with a pop-out center that takes an AirDome if you want to add air to the root zone. Square: fits the 2.2 gal and 3.9 gal AutoPot pots Round: fits the 6.6 gal plastic pot and the 3 gal and 5 gal GeoPots Replaces the pebble drainage layer Pop-out center section for optional AirDome integration With AirDome Kit: adds the AutoPot AirDome Kit (APWS090) Tough, reusable ABS plastic
$10.49 - $22.68
-
AutoPot AutoPot Adaptive Collar for XXL Module Tray
An add-on collar for the XXL tray that narrows the opening to fit the older 9 gal FlexiPot fabric pot, and covers the tray to keep light, algae, debris and evaporation down. The newer 9 gal GeoPot G Lite has the same diameter as the 13 gal, so it doesn't need one. Fits the AutoPot XXL module tray Only needed for the older 9 gal FlexiPot fabric pot Not needed with the 9 gal GeoPot G Lite Helps protect the tray water from light, algae, debris and evaporation
$6.99
-
AutoPot AutoPot XXL Module Tray, With or Without Lid and Grommets
Replacement tray for AutoPot XXL modules and systems. It takes the 9 or 13 gal GeoPot G Lite (the older 9 gal FlexiPot needs the XXL Adaptive Collar). The full set adds the lid, the 3/8" top hat grommet for the supply pipe and the 1/4" blanking grommet for the overflow hole. Takes a 13 gal fabric pot, or a 9 gal FlexiPot with the XXL Adaptive Collar (sold separately) Tray, Lid & Grommets: XXL tray, XXL lid, 3/8" top hat grommet and 1/4" blanking grommet Tray Only: just the tray; lid and grommets not included The 3/8" grommet seals the supply pipe through the tray wall; pull the 1/4" blanking grommet to run outdoors with an overflow AQUAvalve, pipe and fittings sold separately
$24.99 - $32.99
-
AutoPot AutoPot Replacement Tray Lid for 1Pot, XL, easy2grow or XXL Trays
Replacement lids for AutoPot module trays, sold without the tray. Pick the one that matches your tray. 1Pot Tray: fits the 1Pot module tray (2.2/3.9 gal pots) 1Pot XL / GeoPot Tray: fits the newer XL grommeted trays only easy2grow Tray: fits the easy2grow module tray XXL Module Tray: fits the XXL FlexiPot module tray and shields the water in the AQUAvalve compartment from light, algae, debris and evaporation; made in the UK Lid only; tray sold separately
$4.99 - $11.79
-
AutoPot AutoPot AQUAvalve5 Upgrade Kit for 1Pot, 1Pot XL and GeoPot Systems
Converts an older AutoPot 1Pot, 1Pot XL or GeoPot XL system that runs 1/4" (pre-October 2020) valves over to the AQUAvalve5 and its larger-bore 3/8" pipe and fittings. It's the upgrade parts only, not a full system: fit the new grommeted trays and lids, put your pots back in and connect the system as before. Choose your system size (1 to 100 pots) and tray type: 1Pot for 2.2/3.9 gal pots, or 1Pot XL / GeoPot Every kit: one AQUAvalve5 and one grommeted tray and lid per pot, plus 3/8" pipe 1, 2 and 4 pot kits (both tray types) and the standard 6 pot kit also include 3/8" in-line tap(s), a golf filter with filter material and a 3/8" top hat grommet for a hard-tank setup, plus 3/8" cross and tee connectors where the layout needs them The 6 Pot XL kit and all 8 pot and larger kits use 1/2"-3/8" reducing connectors to branch off a 1/2" main line from a FlexiTank (1/2" pipe and tank filter not included) On a 12.4 gal plastic tank, enlarge the grommet hole to 12.5 mm with a step drill, using the 3/8" top hat grommet as the size guide Existing FlexiTank filters and adapters still work; you only need a 1/2"-3/8" filter and adapter to run 3/8" pipe straight from a FlexiTank Pots and reservoir not included
$56.59 - $5,034.09
-
AutoPot AutoPot AQUAvalve5 Upgrade Kit for easy2grow Systems
Converts an older easy2grow system (2Pot trays with 2.2 or 3.9 gal pots) over to the AQUAvalve5 and its larger-bore 3/8" pipe and fittings. It's the upgrade parts only, not a complete system: your trays, pots and lids stay in service. Sizes from a single easy2grow tray up to an easy2grow 100 One AQUAvalve5 per 2Pot tray, plus 3/8" pipe easy2grow, easy2grow 4 and easy2grow 6 kits also include a 3/8" top hat grommet, a golf filter and 3/8" in-line taps (one on the easy2grow, two on the 4 and 6), plus tee connectors on the 4 and 6 easy2grow 12 and larger kits use 1/2"-3/8" reducing cross connectors to branch off a 1/2" main line from a FlexiTank On a 12.4 gal plastic tank, enlarge the grommet hole to 12.5 mm with a step drill Existing easy2grow trays, pots and lids fit the AQUAvalve5 and 3/8" parts
$37.99 - $1,241.79
-
AutoPot AutoPot Module Accessory Pack, AQUAvalve with Pipe and Fittings
The working parts for one AutoPot module: the AQUAvalve, a length of pipe, root control and the fittings to tap into your main line. It drops into your existing module tray, so it's the way to refit a module; trays, lids and pots are sold separately (the XXL packs include the fabric pot). Pick the pack for your module, then AQUAvalve5 (3/8") or the pre-October 2020 AQUAvalve (1/4") to match your fittings. 1Pot Module: AQUAvalve, 3.3 ft of pipe, root control disc, tee and 1/2" reducing tee 1Pot XL Module: AQUAvalve, 3.3 ft of pipe, XL root control disc, tee and 1/2" reducing tee GeoPot Module (pot not included): AQUAvalve, 3.3 ft of pipe, PotSock Round, tee and 1/2" reducing tee easy2grow Kit: AQUAvalve, 2 PotSock Square, 2 root control discs, 4.9 ft of pipe, in-line tap, golf filter and grommet easy2grow Extension: AQUAvalve, 3.3 ft of pipe, 2 root control discs, 2 PotSock Square, tee and 1/2" reducing tee XXL Module 9 or 13 gal (AQUAvalve5 only): AQUAvalve5, 3.3 ft of 3/8" pipe, matching fabric FlexiPot and PotSock, 3/8" top hat grommet, 1/4" blanking grommet, 3/8" tee, 1/2"-3/8" tee and 1/2"-3/8" cross; XXL tray and lid sold separately, and the 9 gal pack also needs the XXL Adaptive Collar AQUAvalve5 packs use 3/8" pipe with 3/8" and 1/2"-3/8" fittings; pre-October 2020 packs use 1/4" pipe with 1/4" and 1/2"-1/4" fittings Every pack includes full instructions
$31.99 - $65.39
-
AutoPot AutoPot AQUAvalve PotSock Kit with Metal Plate
Root control for an AQUAvalve sitting in an open tray: the AQUAvalve PotSock keeps roots clear of the valve. It's the answer for pot sizes the PotSock Round and Square don't cover, and AutoPot recommends using it with the weighted AQUAvalve Cover to hold it in place. Keeps root systems clear of an AQUAvalve in an open tray For pot sizes not covered by the PotSock Round or PotSock Square Use with the AQUAvalve Cover (sold separately) to keep it in position Pairs with large pots such as the FlexiPot 37 gal in an easy2GO setup In the box: 1 AQUAvalve PotSock and 1 metal plate.
$12.89
-
AutoPot AutoPot Spirit Level for Tray2Grow and AQUAvalve Cover
Replacement circular spirit level for checking that a tray sits level, so water spreads evenly. The Tray2Grow uses three and the AQUAvalve Cover takes one. Fits the Tray2Grow rim (3 per tray) and the AQUAvalve Cover (1 per cover) Helps you level the tray so water spreads evenly Sold individually
$1.99
-
AutoPot AutoPot AQUAvalve Replacement Silicone
Replacement silicones for AQUAvalve floats. They press into the recesses in the top and bottom floats; the AQUAvalve5 uses a different silicone on each float (the bottom one is the larger piece), and the AQUAvalve4 silicone fits the AQUAvalve4 and earlier valves. AQUAvalve5 Top Float: the smaller silicone, for the top float AQUAvalve5 Bottom Float: the larger silicone, for the bottom float AQUAvalve4 and Earlier: fits the AQUAvalve4 and older models Bright colors so they're easy to spot; actual color may vary from the photos Sold individually
$0.62
-
AutoPot AutoPot AQUAvalve5 Replacement Float Parts
Replacement floats and caps for the AutoPot AQUAvalve5. Each valve has an upper float carrying two removable float caps and a bottom float with its own silicone, so you can swap out a worn or lost part instead of replacing the whole valve. Upper Float: 1 AQUAvalve5 upper float plus 2 float caps Bottom Float: 1 AQUAvalve5 bottom float plus 1 bottom float silicone Float Cap: single replacement cap; fits all AQUAvalve models (two per upper float)
$1.99 - $8.99
-
AutoPot AutoPot AQUAvalve Cover
A heavy composite cover that sits over an AQUAvalve in any flat tray, and the key part of AutoPot's easy2GO kit. With a valve, a cover and a tank you can water pots in a tray of any shape or size, and it's heavy enough that it doesn't need weighing down. Fits over an AQUAvalve set in a flat tray (AQUAvalve not included) Heavy composite material stays put without a weight Connect the AQUAvalve to a tank with 3/8" pipe and a filter Keep the tray as level as possible; an optional spirit level fits on the cover Use pots of at least 5 liters so small plants aren't sitting in deep water For carnivorous plants, use rainwater only
$11.79
-
AutoPot AutoPot Tray2Grow Root Control Sheet, 37.4" x 13.8"
The copper-treated sheet that goes on top of the Tray2Grow capillary mat to stop roots growing down through the matting toward the AQUAvalve. Size: 37.4" x 13.8" Pre-soak, then lay it copper side up on the capillary matting Copper coating plus copper woven through the fabric; one sheet can last a couple of grow cycles Still reusable after the surface coating oxidizes off
$9.79
-
AutoPot AutoPot Tray2Grow Capillary Matting, 37.4" x 18.3"
Replacement capillary mat for the Tray2Grow. It lies in the tray and wicks water up to the roots of whatever sits on top, whether that's pots, seed trays or a planter. Size: 37.4" x 18.3" Pre-soak it before laying it in the Tray2Grow Tuck it into the two outer lengthwise channels only Always use a Tray2Grow Root Control Sheet on top (sold separately)
$17.99
-
AutoPot AutoPot Tray2Grow Grow Bag Spike, With or Without Capillary Lace
Tray2Grow spikes water grow bags from below. Push the spikes into the base of the Tray2Grow tray and lay the grow bag on top: the spikes pierce the underside, and the capillary lace wicks water, and nutrient solution if you use it, up into the bag. For watering and feeding grow bags on a Tray2Grow Spike with Capillary Lace: spike laced with a strip of capillary material Spike Only: replacement spike without the lace Sold individually
$1.49 - $2.98
-
AutoPot AutoPot Tray2Grow Tray and Lid
The molded Tray2Grow tray is the base of the whole Tray2Grow system, with a channeled floor that spreads water evenly and its own compartment for the AQUAvalve. The full set comes with the lid, grommets and three spirit levels; the lid is also sold on its own as a replacement. Outside: 44" L x 15 3/4" W x 3 7/8" D; inside: 37 1/2" L x 13 5/8" W Channeled base for even irrigation flow AQUAvalve compartment with a grommeted pipe port (AQUAvalve not included) Overflow grommet at the far end: take it out for outdoor growing, leave it in indoors Three circular spirit levels sit in the rim so you can level the tray Runs capillary spikes for grow bags, or capillary matting for pots, seed trays and planters (sold separately) In the box: Tray, Lid & Fittings: 1 tray and lid, 1 x 3/8" grommet, 1 x 1/4" overflow grommet and 3 circular spirit levels. Replacement Lid Only: the lid.
$3.29 - $38.99
-
AutoPot AutoPot Tray2Grow Cover, NewMoon Grows Double Zipper Edition
A handmade fabric cover from NewMoon Grows (New Moon Development Co.) that fits over the Tray2Grow planter bed. It keeps light off the soil and slows moisture loss, and a double zipper lets you reach the mulch layer around one or two plants without taking it off. Fits the Tray2Grow 23.5 gal fabric planter bed and the Grassroots Living Soil Bed Double zipper opens to the mulch layer for one or two plants Elastic tension cord keeps a snug fit, zipped or not Cuts light exposure and moisture loss at the soil surface Custom sewn, black and blue; comes with a limited-edition sticker hang tag
$64.99
-
AutoPot AutoPot Tray2Grow Grassroots Living Soil Kit, Self-Watering Bed
The Grassroots Living Soil Kit pairs AutoPot's gravity-fed Tray2Grow with a Grassroots Living Soil Bed made to fit it, holding roughly 28 to 30 gallons of soil. The AQUAvalve5 keeps the tray topped up and the bed drinks from below by capillary action, with no pumps, timers or power. Fill it with your own living soil, plant straight into it and connect it to a reservoir. Growing bed: custom Grassroots Living Soil Bed, approx. 28-30 gallons MoistureLock liner around the walls, breathable fabric at the bottom for root-zone air Sub-irrigated: AQUAvalve5 gravity feed waters the bed from below; no power needed Made for living soil, organic and no-till growing; reusable crop after crop Optional PVC trellis frame Tank filter options: none, a 3/8" golf filter for 12.4 gal hard tanks, or a 1/2"-3/8" Click Fit filter for FlexiTanks Tray: 44" x 15 3/4" x 3 7/8" outside Works with AutoPot hard tanks and FlexiTank reservoirs (sold separately); soil not included
$184.99 - $224.99
-
AutoPot AutoPot Tray2Grow 4x4 Tent Bundle, Two Tray2Grow Slim Kits
This bundle sets up two AutoPot Tray2Grow Slim Kits side by side in a standard 4' x 4' tent, with the tubing and fittings included. Each tray is fed by an AQUAvalve5 on gravity alone, with no pumps, timers or power, and it works with soil or coco. Choose the tank filter that matches the reservoir you plan to use. Two Tray2Grow Slim Kits plus the tubing and fittings to set them up in a 4' x 4' tent Each tray: 44" L x 15 3/4" W x 3 7/8" D outside; 37 1/2" x 13 5/8" inside AQUAvalve5 gravity-fed watering: no pumps, timers or electricity Set pots straight onto the trays; works with soil and coco Filter options: 3/8" golf filter for an 8 gal or 12.4 gal hard tank with lid, or a 1/2"-3/8" Click Fit tank filter for FlexiTank and FlexiTank Pro reservoirs Reservoir, pots and growing media sold separately
$215.99 - $235.29
-
AutoPot AutoPot Blanking Disc for Auto3XL and Auto9XL Tray Systems
The AutoPot Blanking Disc caps an empty pot site on an Auto3XL or Auto9XL tray lid when the system is only partly planted. Covering the open hole helps cut down on algae, debris and nutrient evaporation. Fits: Auto3XL and Auto9XL tray system lids Use: covers an unused pot site when a tray is not fully planted Helps reduce algae, debris and evaporation from the tray
$10.69
-
AutoPot AutoPot Auto5 System with Five 9 Gal FlexiPots, 4' x 4' Tray
The AutoPot Auto5 puts five 9 gal fabric FlexiPots on a 4' x 4' garden tray under one lid, all fed by a single AQUAvalve5 for minimal upkeep. A step drill is needed for setup (not included); a drill template comes in the box. Reservoir sold separately. Includes: Auto5 lid, 4' x 4' square garden tray and round blue access cover Pots: 5 x 9 gal fabric FlexiPots (BPA-free and lead-free) 1 x AQUAvalve5 with AQUAvalve cover, AQUAvalve PotSock and metal plate for the PotSock Fittings: 3/8" top hat grommet and 3.3 ft of 3/8" pipe, plus a drill template Step drill required for setup (not included) Reservoir sizing (AutoPot minimums): 25 gal FlexiTank or FlexiTank Pro for 1 Auto5, 60 gal for 2, 105 gal for 4, 200 gal FlexiTank for 8, 265 gal FlexiTank for 10 Reservoir not included
$410.19
-
AutoPot AutoPot Auto8 Tray System, Eight 3.9 Gal Pots
The AutoPot Auto8 runs eight square 3.9 gal pots on one tray and lid assembly fed by a single AQUAvalve5, with fewer parts to maintain and a smaller footprint than eight single trays. The tray also takes 2.2 gal pots without any adjustment, so plants at different stages can share it. Reservoir sold separately. Includes: Auto8 tray, lid and access cover Pots: 8 x 3.9 gal square pots with 8 x Root Control Squares and 8 x PotSock Squares 1 x AQUAvalve5 with AQUAvalve5 cover, 3/8" top hat grommet and 3.3 ft of 3/8" pipe Also takes 2.2 gal pots (sold separately); swap sizes without adjusting the tray Draws no more water than eight single 1Pot trays Reservoir sizing (AutoPot minimums): 25 gal FlexiTank or FlexiTank Pro for 1 Auto8, 60 gal for 2, 105 gal for 4, 200 gal FlexiTank for 8, 265 gal FlexiTank for 10 Reservoir not included
$447.59
-
AutoPot AutoPot Auto8 Tray System, Eight 2.2 Gal Pots
The AutoPot Auto8 runs eight square 2.2 gal pots on one tray and lid assembly fed by a single AQUAvalve5, with fewer parts to maintain and a smaller footprint than eight single trays. The tray also takes 3.9 gal pots without any adjustment, so plants at different stages can share it. Reservoir sold separately. Includes: Auto8 tray, lid and access cover Pots: 8 x 2.2 gal square pots with 8 x Root Control Squares and 8 x PotSock Squares 1 x AQUAvalve5 with AQUAvalve5 cover, 3/8" top hat grommet and 3.3 ft of 3/8" pipe Also takes 3.9 gal pots (sold separately); swap sizes without adjusting the tray Draws no more water than eight single 1Pot trays Reservoir sizing (AutoPot minimums): 25 gal FlexiTank or FlexiTank Pro for 1 Auto8, 60 gal for 2, 105 gal for 4, 200 gal FlexiTank for 8, 265 gal FlexiTank for 10 Reservoir not included
$425.59
You have seen 72 out of 252 products